International Rotating Equipment Conference 2019 – Programme is available now

0
51

 

The program of the International Rotating Equipment Conference 2019 from 24 to 25 September 2019 is available just from now on. This Conference will take place in Wiesbaden, Germany, Conference Center.

You will find here all papers held at the 12th International Pump User Forum – part of the International Rotating Equipment Conference 2019:

24 September 2019

Plenary Session

09:00 – 10:30: Welcome and Opening, Welcome Address, Plenary Lectures

Session 1 Centrifugal pumps – Energy optimisation

11:00 – 11:30 New control mode to decrease energy consumption of circulator pumps

11:30 – 12:00  Inlet guide vanes control for storage pump

Session 2 Legal frame conditions

11:00 – 11:30 Differences and similarities of ATEX and IECEx – Analysis of the legal framework and market access

11:30 – 12:00  Increasing the energy savings of motor applications: The Extended Product Approach

Session 3 Future drive technology

11:00 – 11:30  Evolution mikro – Smallest amount dosing in the highpressure range thanks to innovative drive technology

11:30 – 12:00 New generation of power drive systems for pump applications

Session 4 Centrifugal pumps – Performance characteristics

14:30 – 15:00 Analysis of the pressure-side recirculation influence on the head production of a radial pump at strong part load

15:00 – 15:30 Numerical analysis of the flow patterns causing the performance curve  instability of a high specific speed centrifugal pump

15:30 – 16:00 Modelling of wall roughness in flow simulations

Session 5 Digital transformation

14:30 – 15:00 Business cases for connected pumps and compressors

15:00 – 15:30 Digitization of pumps – Industrie 4.0 submodels for liquid and vacuum pumps

15:30 – 16:00 Embedded operation point detection system for sidechannel pumps on basis of neural networks

Session 6 Positive displacement pumps

14:30 – 15:00 New process-safe diaphragm positioning system in oscillating displacement pumps with integrated thermal protection device

15:00 – 15:30 ERP positive displacement pumps – Experimental validation of a typeindependent efficiency model

15:30 – 16:00 CFD analysis of cone valves for oscillating positive displacement pump

Session 7 Centrifugal pumps – Simulation methodology

16:30 – 17:00 Rotordynamic simulation of centrifugal pumps considering nonlinear journal bearings including misalignment, local contact and accumulated wear

17:00 – 17:30 Balance between efficiency and cavitation – An approach for pump impeller design and optimization using inverse design and 3D CFD

17:30 – 18:00 A rule-based method for finite element calculation of boiler feed pump casings by parametrized models

Session 8 New challenges for pumps and systems

16:30 – 17:00 Improving the efficiency of a pump fleet by designing pumps specially for individual fixed speed drives

17:00 – 17:30 Systemic optimization of booster stations – From data collection to validation

17:30 – 18:00 Reduction of complexity by smart integration and separation of functions

Session 9 Rotating displacement pumps

16:30 – 17:00 Pumping of challenging products with hermetically tight magnet driven screw pumps

17:00 – 17:30 Towards model-based condition monitoring for progressing cavity pumps

17:30 – 18:00 Fluid flow optimization in rotating positive displacement pumps with focus on perfect cleanability based on scientific proven CFD flow simulation and real tests

25 September 2019

Session 10 Centrifugal pumps – Multiphysics

08:30 – 09:00 Numerical investigation of the flow-induced noise in a centrifugal pump

09:00 – 09:30 Numerical characterisation of the dynamics of thin flexible structures in a sewage pump

09:30 – 10:00  Experimental investigation and 3D-CFD simulation of centrifugal pumps for gasladen liquids with closed and semi-open impellers

Session 11 Submersible pumps

08:30 – 09:00 How can the effect of iron ochre on submersible motor pumps be reduced?

09:00 – 09:30 Optimization of output of a solar powered deepwell pumpsets using information technology tools

09:30 – 10:00 Line start permanent magnet synchronous submersible motor in combination with a modular submersible pump

Session 12 Centrifugal pumps – Product lubricated bearing

08:30 – 09:00 Measuring and simulation of fluid forces in annular gaps – Generic experiments covering the relevant parameter range for turbulent and laminar flow in pumps

09:00 – 09:30 CAPM vs. bulk flow – reliable and efficient prediction of forces and leakage for annular gaps in pumps

09:30 – 10:00 Extension of a Reynolds equation based solver to consider the lomakin effect in axially-flown journal bearings of pumps

Session 13 Availability (Cavitation)

10:30 – 11:00 The relation between suction performance and reliability – a critical review of suction specific speed limitations

11:00 – 11:30 Performances evolution in 4 quadrant operation under cavitation

Session 14 Sewage pumps

10:30 – 11:00 Functional performance assessment of wastewater pumps – validation with pumps from the field

11:00 – 11:30 Experimental and numerical analysis of transient flow characteristics in single-blade and two-blade pumps

Session 15 Condition monitoring I

10:30 – 11:00 Enhance autonomous maintenance by utilizing local condition monitoring tool

11:00 – 11:30 A holistic approach for pump system analytics

Session 16 Cavitation

14:00 – 14:30 Influence of surface texture on cavitation inception

14:30 – 15:00 Transient flow mechanisms of cavitation in side channel pumps

Session 17 Reliability I

14:00 – 14:30 Pump failures, often more than just one problem – A system approach

14:30 – 15:00 Non-intrusive measurement of pressure pulsations using a re-usable wire strain sensor

Session 18 Condition monitoring II

14:00 – 14:30 A self-learning binary controller for energy efficient pump operation

14:30 – 15:00 Concept validation of a soft sensor network for wear detection in positive displacement pumps

Session 19 Materials and manufacturing

15:30 – 16:00 Development of high performance economical fe-based corrosion and erosion protective coating for pump parts

16:00 – 16:30 Progress with hybrid – An additive manufacturing technology for closed impellers

Session 20 Reliability II

15:30 – 16:00 Investigating the chronic high temperature reading on the lube oil system of water injection pumps

16:00 – 16:30 Replacement of a mechanical sealed pump with a vertical erected canned motor pump in the course of capacity expansion of a steamcracker

Session 21 Data management

15:30 – 16:00 Development of a digitalized wastewater pumping station test bed

16:00 – 16:30 From notebooks to datapipelines – The Darmstadt approach to handling measurement data and metadata

Final Plenary Session

16:30 – 16:45 Closing remarks

Registration for the International Rotating Equipment Conference 2019 from 24 to 25 September 2019 has begun. “Experts and interested parties can register easily and conveniently online for this international top-level network,” says Christoph Singrün, Managing Director of VDMA Pumps + Systems and Compressors, Compressed Air and Vacuum Technology. “Benefit from an early registration and use the early booking discount. We grant this until and including 31 May 2019.”

http://www.introequipcon.com

 

LEAVE A REPLY

Please enter your comment!
Please enter your name here

This blog is kept spam free by WP-SpamFree.